manualshive.com logo in svg

Siemens SENTRON PAC2200, Product Manual, Page: 12 / 130

Share
Download
Siemens SENTRON PAC2200 Product Manual Download Page 12

Introduction 

 

1.5 Advanced training courses 

 

PAC2200 

10

 

Equipment Manual, 12/2019, L1V30415167B-03 

information during the period required by the applicable OSS licenses by contacting the 

following address:  
Siemens AG  

Smart Infrastructure 

Low Voltage Products  

Technical Support  

Postfach 10 09 53  

93009 Regensburg 

Germany 
www.siemens.com/lowvoltage/support-request 

(

https://support.industry.siemens.com/cs/us/en/ps

) 

Keyword: Open Source Request (please specify Product name and version, if applicable)  
SIEMENS may charge a handling fee of up to 5 EUR to fulfil the request.  
Warranty regarding further use of the Open Source Software  
SIEMENS' warranty obligations are set forth in your agreement with SIEMENS. SIEMENS 

does not provide any warranty or technical support for this Product or any OSS components 

contained in it if they are modified or used in any manner not specified by SIEMENS. The 

license conditions may contain disclaimers that apply between you and the respective 

licensor. For the avoidance of doubt, SIEMENS does not make any warranty commitment on 

behalf of or binding upon any third-party licensor. The Open Source Software used in the 

product and the license agreements concerning this software can be found in the 

Readme_OSS. 

1.5

 

Advanced training courses 

Find out about training courses on offer on the following link. 
Training for Industry (

https://www.siemens.com/sitrain-lowvoltage

)  

This is where you can choose from 

●

 

Web-based training courses (online, informative, free) 

●

 

Classroom training courses (course attendance, comprehensive, subject to fee) 

. 
You also have the possibility of compiling your own training portfolio via Learning paths. 

Summary of Contents for SENTRON PAC2200



































































































































Reviews:

No comments