manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 77 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 77

 

Connection 

 

7.2 Connection of the power supply 

3KC ATC6300 transfer control device 
Manual, 03/2018, L1V30535632002A-01 

75

 

Network/generator transfer 

The output Control Generator 2 must then be programmed in such a way that the generator 

is started when the ATC6300 is de-energized.  

 

Connection 

Parameter 

Output type 

Setting 

OUT (3) 22 - 23 

P11.03.01 

NOR 

Control Generator 2 

Generator/generator transfer  

The output Control Generator 2 must then be programmed in such a way that the generator 

is started when the ATC6300 is de-energized. 

 

Connection 

Parameter 

Output type 

Setting 

OUT (3) 22 - 23 

P11.03.01 

NOR 

Control Generator 2 

OUT (2) 11 - 12 

P11.02.01 

REV 

Control Generator 1 

7.2.6

 

Recommended implementation for gen-set application (without power supply by 

means of a DC source) 

If gen-sets are used, the following connection is recommended:  

 

The auxiliary power supply is controlled by the ATC6300. The use of the dual network 

connection accessory is optional.  

 

Connection 

Parameter 

Setting 

OUT (1) 9 - 10 

P11.01.01 

Line 1 status 

Network/generator transfer 

The output Control Generator 2 must then be programmed in such a way that the generator 

is started when the ATC6300 is de-energized.  

 

Connection 

Parameter 

Output type 

Setting 

OUT (3) 22 - 23 

P11.03.01 

NOR 

Control Generator 2 

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments