manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 28 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 28

Product description 

 

4.5 Display pages of the ATC6300 

 

3KC ATC6300 transfer control device 

26

 

Manual, 03/2018, L1V30535632002A-01 

It shows 

●

 

the threshold values of the voltage between L-L and between L-N (if set) 

●

 

the threshold values of the minimum and maximum frequency 

If a threshold value is exceeded/undershot, it is shown with a black background, which 

means that it is possible to check in real time in the Control Thresholds menu which 

parameter of the voltage supply is causing problems. 

Alarms status  

 

①

 

Active alarm 

The Alarms Status submenu lists all possible alarms of the ATC6300. If an alarm is active 

the corresponding alarm has a black background.  

Statistics  

 

①

 

Line 2 

②

 

Counter of the switching operations in the automatic mode for Line 2 

③

 

Alarm counter A04 

④

 

Time during which the line is within the defined thresholds 

⑤

 

Elapsed time in which the load has zero current 

⑥

 

Counter of the deactivation processes 

⑦

 

Time during which the line was outside the defined thresholds 

⑧

 

Time in which the power supply was maintained by Line 1 

⑨

 

Counter of the switching operations in the manual mode for Line 1 

⑩

 

Line 1 

The transfer behavior is shown in the Statistics submenu.  

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments