manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 168 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 168

MODBUS communication 

 

11.6 Data library 

 

3KC ATC6300 transfer control device 

166

 

Manual, 03/2018, L1V30535632002A-01 

11.6.4

 

Status of the ATC (use with MODBUS function 03 and 04) 

 

 

Address   Words  Function 

Format 

2210H 

2 

Status of the ATC (bit 0 - bit 31) 

unsigned integer 

The meaning of the 32 bits of the address 2210H can be viewed below:  

 

Bit 

Meaning  

0 

ATC OFF 

1 

ATC in MAN mode 

2 

ATC in AUT mode 

3 

ATC in Test mode 

4 

Voltage Line 1 OK 

5 

Voltage Line 2 OK 

6 

LED Line 1 enabled 

7 

LED Line 2 enabled 

8 

LED load on Line 1 enabled 

9 

LED load on Line 2 enabled 

10 

Mains breaker closed 

11 

Generator breaker closed 

12 

Global alarm 

13 

AC power supply 

14 

Start generator 1 

15 

Start generator 2 

16 

Line 1 maximum voltage 

17 

Line 1 minimum voltage 

18 

Line 1 maximum frequency 

19 

Line 1 minimum frequency 

20 

Line 1 phase failure 

21 

Line 1 phase unbalance 

22 

Line 2 maximum voltage 

23 

Line 2 minimum voltage 

24 

Line 2 maximum frequency 

25 

Line 2 minimum frequency 

26 

Line 2 phase failure 

27 

Line 2 phase unbalance 

28 

Not used 

29 

Not used 

30 

Not used 

31 

Not used 

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments