manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 157 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 157

 

MODBUS communication 

 

11.4 MODBUS functions 

3KC ATC6300 transfer control device 
Manual, 03/2018, L1V30535632002A-01 

155

 

Error messages  

If the slave contains an incorrect message, it responds with a message consisting of the 

queried function with 80Hex, followed by an error code byte.  
The error codes that are sent to the master are listed below: 

 

Code  Error 
01 

Illegal function 

02 

Invalid address 

03 

Parameter outside the setting range 

04 

Version of function not possible 

06 

Slave is overloaded, the function is not currently available 

CRC calculation  

Information on the CRC calculation can be found under www.modbus.org in the MODBUS 

over Serial Line Specification and Implementation Guide 

(

http://www.modbus.org/docs/Modbus_over_serial_line_V1_02.pdf

). 

LRC calculation 

Information on the LRC calculation can be found under www.modbus.org in the MODBUS 

over Serial Line Specification and Implementation Guide 

(

http://www.modbus.org/docs/Modbus_over_serial_line_V1_02.pdf

). 

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments