manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 102 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 102

Connection 

 

7.3 Connection of Siemens SENTRON switching devices 

 

3KC ATC6300 transfer control device 

100

 

Manual, 03/2018, L1V30535632002A-01 

Programming of the parameters for the circuit diagram illustrated here 

 

Terminal 

Parameter code 

Setting 

--- 

P05.07 

Changeover pulse or changeover continuous 

15(INP1) 

P10.01.01 

Line 1 breaker closed (feedback 1) 

16(INP2) 

P10.02.01 

Line 2 breaker closed (feedback 2) 

25(OUT4) 

P11.04.01 

Open Line 1 / Line 2 

27(OUT5) 

P11.05.01 

Close Line 1 contactor/circuit breaker 

30(OUT7) 

P11.07.01 

Close Line 2 contactor/circuit breaker 

Optional: 
17(INP3) 

P10.03.01 

Configurable 

 

P10.03.03 

NC (normally closed contacts) 

 

P15.01.01 

INPx 

 

P15.01.02 

3 

 

P15.01.03 

RTSE not available 

1)

 

18(INP4) 

P10.04.03 

 

 

P10.04.01 

Emergency 

2)

 

 

1)

  This message appears if the 3KC3 / 4 is in the manual mode, if it is de-energized, or if there is a mechanical defect on 

the RTSE. 

2) 

  When the optional emergency pushbutton is confirmed, this message appears and the ATC switches the RTSE to the 

OFF position. 

The following parameters must be observed for the 3KC3 / 3KC4. 

 

Parameter code  Description 

Setting 

P05.03  

Line 1 

→ Line 2 interlock time

 

 

≥ 6 s

 

P05.04  

Line 1 ← Line 2 interlock time

 

 

≥ 6 s

 

P05.06 

Maximum operating switch time 

 

≥ 5 s

 

P05.08  

Opening pulse duration 

≥ 1 s

 

P06.03  

Min voltage delay (Line 1) 

≥ 1 s

 

P06.06  

Max voltage delay (Line 1) 

≥ 1 s

 

P06.07  

Presence delay (when Line 2 source not available) 

≥ 5 s

 

P06.08 

Presence delay (when Line 2 source available) 

≥ 5 s

 

P07.03  

Min voltage delay (Line 2) 

≥ 1 s

 

P07.06  

Max voltage delay (Line 2) 

≥ 1 s

 

P07.07  

Presence delay (when Line 1 source not available) 

≥ 5 s

 

P07.08  

Presence delay (when Line 1 source available) 

≥ 5 s

 

A03 

Property: Retained alarm (see chapter Properties of alarms (Page 47) and Alarm table 

(Page 49))  

Disabled 

Property: Lock BRK1 (see chapter Properties of alarms (Page 47) and Alarm table 

(Page 49)) 

A04 

Property: Retained alarm (see chapter Properties of alarms (Page 47) and Alarm table 

(Page 49))  

Disabled 

Property: Lock BRK2 (see chapter Properties of alarms (Page 47) and Alarm table 

(Page 49)) 

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments