manualshive.com logo in svg

Siemens SENTRON 7KT PAC1600 Series, Manual, Page: 51 / 76

Share
Download
Siemens SENTRON 7KT PAC1600 Series Manual Download Page 51

 

7KT multimeter 
Manual, 08/2018, 2514284149-01 

49

 

 

Commissioning 

6 

6.1

 

Overview 

Prerequisites 

●

 

The device has been installed. 

●

 

The device has been connected in accordance with the possible connection methods. 

Steps for starting up the device 

 

 

NOTICE 
Risk of malfunction or device failure! 
Incorrect connection can result in malfunctions and failure of the device. 

•

 

Before connecting the device, ensure that the local power supply conditions match the 

specifications on the type plate. 

•

 

Before starting up the device, check that all connections are correct. 

 

 

Note 
Before performing an insulation test of the entire installation with AC or DC, you must 

disconnect the device from the line voltage. 

 

1.

 

Apply the measuring voltage. You can find more information on this in chapter 

Connecting (Page 41). 

2.

 

Parameterize the device. You can find more information on this in chapter Parameterizing 

with powerconfig (Page 50). 

3.

 

Check the measured values. 

 

Summary of Contents for SENTRON 7KT PAC1600 Series













































































Reviews:

No comments