manualshive.com logo in svg

Siemens SENTRON 7KT PAC1600 Series, Manual, Page: 30 / 76

Share
Download
Siemens SENTRON 7KT PAC1600 Series Manual Download Page 30

Description 

 

3.4 Parameterization 

 

7KT multimeter 

28

 

Manual, 08/2018, 2514284149-01 

3.4.5

 

Alarm display 

If alarms are activated, the multimeter displays the page with the corresponding status and 

the following format: 

 

①

 

Alarm deactivated 

②

 

Alarm text activated 

③

 

Alarm code activated 

④

 

Alarm activated 

●

 

If the alarm is activated, ON flashes with the triangle symbol. 

●

 

If the alarm is deactivated, OFF is displayed continuously. 

●

 

If no alarm is programmed, dashes are displayed. After approx. 3 s, the scrolling text for 

the alarm programmed in parameter P09.n.05 appears. 

●

 

If several alarms are active, the alarm text changes on the display. 

●

 

You can use parameter P02.14 for the Utility menu to make the backlighting of the 

display flash in the event of an alarm. This makes it more obvious that a fault has 

occurred. 

●

 

Depending on the settings of parameter P09.n.03, alarms are either reset automatically 

when the alarm conditions are no longer fulfilled or they need to be reset by you manually 

via the command menu (C.07). 

You can find more information on parameters P09 in chapter Parameter setting (setup) from 

the front panel (Page 23). 
You can find more information on parameters P09 and C.07 in chapter Command menu 

(Page 36). 

3.4.6

 

Parameter tables 

The tables show all the available programming parameters with the possible setting range, 

the factory setting and a description of the parameter function. 

Summary of Contents for SENTRON 7KT PAC1600 Series













































































Reviews:

No comments