manualshive.com logo in svg

Siemens SENTRON 7KT PAC1600 Series, Manual, Page: 16 / 76

Share
Download
Siemens SENTRON 7KT PAC1600 Series Manual Download Page 16

Description 

 

3.2 Measuring inputs 

 

7KT multimeter 

14

 

Manual, 08/2018, 2514284149-01 

3.2

 

Measuring inputs 

3.2.1

 

Current measurement 

 

 

NOTICE 
Device damage due to DC current 
The device is not suitable for measuring DC current. 
Only measure AC current with the device. 

 

Design of the device 

The devices are designed for a rated current of 1 A or 5 A for connecting standard current 

transformers. 

Ampacity of current measuring inputs 

The current measuring inputs can be continuously loaded as follows: 

●

 

With 1.2 A at a rated current of 1 A 

●

 

With 6 A at a rated current of 5 A 

3.2.2

 

Voltage measurement 

 

 

NOTICE 
Device damage due to DC current 
The device is not suitable for measuring DC current. 
Only measure AC current with the device. 

 

Design of the device 

The device is designed for: 

●

 

Direct measurement on the grid 

●

 

Nominal voltage 364 V/600 V 

Summary of Contents for SENTRON 7KT PAC1600 Series













































































Reviews:

No comments