manualshive.com logo in svg

Siemens SENTRON 7KT PAC1600 Series, Manual, Page: 12 / 76

Share
Download
Siemens SENTRON 7KT PAC1600 Series Manual Download Page 12

Safety instructions 

 

2.1 Safety instructions 

 

7KT multimeter 

10

 

Manual, 08/2018, 2514284149-01 

 

NOTICE 
Device damage due to condensation 
Humidity may cause condensation on the device if temperature balance has not been 

reached. Condensation may damage the device when it is connected to the power supply. 
Do not connect the device to the power supply until temperature balance has been 

reached. To achieve temperature balance, place the device in the operating room for a 

period of at least two hours. 

 

 

Note 
RS 485 termination recommended 
In order to avoid reflection on the bus cable, we recommend fitting a 120 

Ω terminating 

resistor at the beginning and end of the bus cable. 
To establish Modbus RTU communication, the communication parameters must be known. 

These include baud rate and format. Furthermore, you must have entered the slave address 

in the device. 

 

 

Note 
Risk of manipulation! 
In order to reduce the risk of manipulation occurring on the device, it is recommended that 

the protective mechanisms available in the device are activated. 
Default passwords for the protective mechanisms: 

•

 

Use 1000 for user rights without write access. 

•

 

Use 2000 for extended rights with write access. 

Use a lead seal on the cover for security. 

 

Safety-related symbols on the device 

 

Symbol 

Meaning 

 

Risk of electric shock 

 

Electrical installation demands technical competence 

 

Summary of Contents for SENTRON 7KT PAC1600 Series













































































Reviews:

No comments