Siemens SENTRON 3WL Function Manual Download

Page: 9 / 146

Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01

Introduction

1.1

General

The Library SENTRON 3WL / 3VL for SIMATIC PCS 7 software package is used to connect

the circuit breakers SENTRON 3WL and 3VL to a SIMATIC PCS 7 process control system

and contains the following components:
●

Block library with:
–

DIA_WLVL: diagnostic block

–

DRV_3WL: PCS 7 block for recording measurements, setpoints, protective

parameters, etc. of a 3WL circuit-breaker

–

DRV_3VL: PCS 7 block for recording measurements, setpoints, protective

parameters, etc. of a 3VL circuit breaker

–

User objects and operating blocks for operating and observing measured data on the

●

Online help in German and English

●

Manual in German and English

The block library can be used in in the PCS 7 versions V6.1 SP1, V7.0 and V7.0 SP1.

1.2

Further documentation

You can find further details in the following manuals:
●

Manual for SENTRON WL and SENTRON VL circuit-breakers with communication

capability

●

SENTRON WL Operating Manual

●

SENTRON VL Operating Manual

1.3

Installing the library

To start the installation, please insert the CD in the CD-ROM drive on your PG/PC and

launch the "Setup.exe" program. All the other information you need will be provided during

the installation process. Please also read the information in the readme file.

Summary of Contents for SENTRON 3WL



















































































































































Search results

Summary of Contents for SENTRON 3WL

Reviews:

Related manuals for SENTRON 3WL

Brands by name

Popular brands

Siemens SENTRON 3WL, Function Manual

Search results

Summary of Contents for SENTRON 3WL

Reviews:

Related manuals for SENTRON 3WL

Brands by name

Popular brands