Siemens SENTRON 3WA System Manual Download

Page: 81 / 82

3WA Air Circuit Breaker Communication
System Manual, 11/2021, 92310000004-02

List of abbreviations

B.1

Table of abbreviations

Abbreviation

Meaning

Alarm

BSS

Breaker status sensor

COM

Communication module

CSA

Canadian Standards Association

DAS+

Dynamic Arc-Flash Sentry

DIN

Deutsches Institut für Normung e. V. (German Institute for Standardization)

ESD

Electrostatic sensitive device

European Standard

ESD

Electrostatic sensitive device

ETU

Electronic Trip Unit

G alarm

Ground-fault alarm

G tripping

Ground-fault tripping

Ground fault

I tripping

Instantaneous short-circuit tripping

IEC

International Electrotechnical Commission

IOM

Input/output module

Phase 1

Phase 2

Phase 3

L tripping

Inverse-time delayed overload tripping

LED

Light emitting diode

MLFB

Machine-readable product code (German acronym)

Neutral conductor

N 117

Australian approval mark

NEMA

National Electrical Manufacturers Association

NIOSH

National Institute for Occupational Safety and Health

N tripping

Tripping due to overcurrent in the N-conductor

OSHA

Occupational Safety and Health Administration

S tripping

Short-time delayed short-circuit tripping

TUI

Trip Unit Interface (local communication interface)

VDE

Verband der Elektrotechnik Elektronik und Informationstechnik e. V. (Ger-

man Association for Electrical, Electronic and Information Technologies)

WBT

Web-based training

Terminal marking according to DIN

Summary of Contents for SENTRON 3WA



















































































Search results

Summary of Contents for SENTRON 3WA

Reviews:

Related manuals for SENTRON 3WA

Brands by name

Popular brands

Siemens SENTRON 3WA, System Manual

Search results

Summary of Contents for SENTRON 3WA

Reviews:

Related manuals for SENTRON 3WA

Brands by name

Popular brands