Siemens SCALANCE XR524-8C Operating Instructions Manual Download Page 97

Page: 97 / 100

Certification

10.1 FDA and IEC marks

SCALANCE XR-500
Operating Instructions, 05/2014, A5E03275845-05

cULus Approval Hazardous Location

cULus Listed I. T. E. FOR HAZ. LOC.
Underwriters Laboratories Inc. complying with

●

UL 60950-1 (Information Technology Equipment)

●

ANSI/ISA 12.12.01-2007

●

CSA C22.2 No. 213-M1987

Approved for use in

Cl. 1, Div. 2, GP A, B, C, D T4

Cl. 1, Zone 2, GP IIC T4
Report no. E240480

Note
Only variants with 24 VDC power supply meet the requirements of this approval.

EU declaration of conformity

You will find EC declaration of conformity for these products on the Internet pages of

Siemens Industry Online Support

(

http://support.automation.siemens.com/WW/view/en/33118389/134200

10.1

FDA and IEC marks

The following devices meet the FDA and IEC requirements listed below:

Device

Fulfills FDA and IEC requirements

SCALANCE XR524-8C

SCALANCE XR528-6M

SCALANCE XR552-12M

Note: With modular devices , the marking is on the MM900 media modules and the SFP and SFP+ transceivers.

Figure 10-1 FDA and IEC approvals

Summary of Contents for SCALANCE XR524-8C





































































































Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands

Siemens SCALANCE XR524-8C, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands