Siemens SCALANCE XR524-8C Operating Instructions Manual Download Page 93

Page: 93 / 100

SCALANCE XR-500
Operating Instructions, 05/2014, A5E03275845-05

Certification

The SIMATIC NET products described in these Operating Instructions have the approvals

listed below.

Note
Issued approvals on the type plate of the device
The specified approvals apply only when the corresponding mark is printed on the product.

You can check which of the following approvals have been granted for your product by the

markings on the type plate.

EC directives

SIMATIC NET products meet the requirements and aims of the following EC directives.

EMC directive (electromagnetic compatibility)

The SIMATIC NET products described in these operating instructions meet the requirements

of EC directive 2004/108/EC "Electromagnetic Compatibility" for the following areas of

application:

Field of application

Requirements

Emission

Immunity to interference

Industry

EN 61000-6-4 : 2007

EN 61000-6-2 : 2005

C-TICK

The product meets the requirements of the AS/NZS 2064 standard (Class A).

Summary of Contents for SCALANCE XR524-8C





































































































Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands

Siemens SCALANCE XR524-8C, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands