Siemens SCALANCE XR524-8C Operating Instructions Manual Download Page 72

Page: 72 / 100

Upkeep and maintenance

7.3 Downloading new firmware using TFTP without WBM and CLI

SCALANCE XR-500

Operating Instructions, 05/2014, A5E03275845-05

7.3

Downloading new firmware using TFTP without WBM and CLI

Firmware

The firmware is signed and encrypted. This ensures that only firmware created by Siemens

can be downloaded to the device.

Procedure with Microsoft Windows

Using TFTP, you can supply a device with new firmware even when it cannot be reached

using WBM or CLI. This section explains the procedure based on the example of Microsoft

Windows.
Follow the steps below to load new firmware using TFTP:
1.

Turn off the power to the device.

Now press the "SELECT/SET" button and reconnect the power to the device while

holding down the button.

Hold down the button until the red fault LED "F" starts to flash after approximately 30

seconds.

Now release the button. The bootloader of the device waits in this status for a new

firmware file that you can download by TFTP.

Connect a PC to the out-band interface of the device via an Ethernet cable.

Assign an IP address to the device using DHCP or the Primary Setup Tool.

Open a Windows command prompt and change to the directory where the file with the

new firmware is located and then execute the following command :

tftp -i <IP address> put <firmware file>

Note
You can enable TFTP in Microsoft Windows as follows:
"Control Panel" > "Programs and Features" > "Turn Windows features on or off" > "TFTP

Client".

Once the firmware has been transferred completely to the device and validated, there is

an automatic restart on the device. This may take several minutes.

Summary of Contents for SCALANCE XR524-8C





































































































Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands

Siemens SCALANCE XR524-8C, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands