Siemens SCALANCE XR524-8C Operating Instructions Manual Download Page 57

Page: 57 / 100

Connecting

5.4 Signaling contact

SCALANCE XR-500
Operating Instructions, 05/2014, A5E03275845-05

5.4

Signaling contact

Information on the signaling contact

The signaling contact (relay contact) is a floating switch that signals faults by breaking the

contact. The signaling contact is connected to a 2-pin plug-in terminal block.

NOTICE
Damage due to voltage being too high
The maximum load on the signaling contact is 24 VDC and 100 mA (safety extra-low

voltage (SELV)).
Higher voltages or currents can damage the device!

Position and assignment

Figure 5-10 Position of the signaling contact on a SCALANCE XR524-8C

Figure 5-11 Position of the signaling contact on a SCALANCE XR552-12M. SCALANCE XR528-6M

is analogous.

Summary of Contents for SCALANCE XR524-8C





































































































Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands

Siemens SCALANCE XR524-8C, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands