Siemens SCALANCE XR524-8C Operating Instructions Manual Download Page 31

Page: 31 / 100

Assembling

4.2 Types of installation

SCALANCE XR-500
Operating Instructions, 05/2014, A5E03275845-05

4.2

Types of installation

Mounting the IE switches

For the devices, you have the following options:

●

19" rack mounting

●

Desktop operation with adhesive feet

●

Secured at 4 points using special mounting brackets

Mounting modular components

For the modular components, you have the following options:

●

Plugging/pulling media modules in the module slots

●

Inserting/removing SFP transceivers in media modules for SFP or SFP+ slots

●

Inserting/removing SFP+ transceivers in SFP+ slots

●

Mounting power supply units

4.3

19" rack mounting

Notes on 19" rack mounting

Note
Mounting with two mounting brackets
The device is installed using two mounting brackets on the front of the rack device.
After fitting the two mounting brackets, the rack device can then be installed in a 19" cabinet.

Note
Installation secured at 4 points
Where mechanical strain is liable to be high, for example when used on a ship, four-point

mounting is necessary.
You will find details in the sections "Four-point mounting (Page 34)" and "Mechanical

stability (in operation) (Page 98)".

Summary of Contents for SCALANCE XR524-8C





































































































Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands

Siemens SCALANCE XR524-8C, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR524-8C

Reviews:

Related manuals for SCALANCE XR524-8C

Brands by name

Popular brands