Siemens SCALANCE XR-500 Operating Instructions Manual Download Page 92

Page: 92 / 112

Technical data

8.4 Technical specifications of the SCALANCE XR552-12M

SCALANCE XR-500

Operating Instructions, 05/2017, A5E03275845-11

Technical specifications
Ambient temperature

Operation without filter pad and with-

out SFP+ LH transceiver up to 2000 m

0 °C to +60 °C

When operating as of 2000 m

The maximum ambient temperature is

reduced by 5°C

During storage

40 ℃ to +70 ℃

During transportation

40 ℃ to +70 ℃

Relative humidity

During operation at 25 ℃

≤ 95%, no condensation

Design, dimensions and weight
Weight (basic device without media

modules)

10 kg

Degree of protection (with closed ser-

vice panel)

IP20

Dimensions without brackets for

19" rack mounting (W x H x D)

446 x 133 x 305 mm (3 height units)

Installation options

•

19" rack mounting

•

Desktop operation

•

Four-point mounting

Design of the mounting bracket for use on ships
Dimensions without brackets for

19" rack mounting (W x H x D)

60 x 130.5 x 18.3 mm (3 height units)

Plate thickness

1.5 mm

Bending radii

1.5 mm

Surface of the housing

Stainless steel X6CR17

Mean time between failure (MTBF)

•

Basic device without media mod-

ules

•

at 40 °C ambient temperature

> 15.7 years

Depending on which components you use, the maximum ambient temperature can

change, see section "Permitted ambient temperature (Page 19)".

Note
ISO tolerance and punching burr
For dimensions without tolerance details, the general tolerances "medium" acc. to DIN ISO

2768 apply. No punching burrs are permitted.

Summary of Contents for SCALANCE XR-500

















































































































Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands

Siemens SCALANCE XR-500, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands