Siemens SCALANCE XR-500 Operating Instructions Manual Download Page 53

Page: 53 / 112

Assembling

4.8 Mounting power supply units

SCALANCE XR-500
Operating Instructions, 05/2017, A5E03275845-11

Procedure

Figure 4-4

19" rack mounting of the power supply unit

To mount the PS598-1 power supply unit in a 19" rack, follow the steps below:
1.

Secure the two mounting brackets with four screws each (M3 x 6 supplied with the

product) to the side panels of the power supply unit

①

The maximum tightening torque for these screws is 0.5 Nm.

Screw the PS598-1 power supply unit to the 19" rack

②

4.8.2

Mounting the PS598-1 power supply unit on the rear panel of modular device

You can mount the PS598-1 power supply unit on the rear panel of the following devices:

●

SCALANCE XR528-6M

●

SCALANCE XR552-12M

Summary of Contents for SCALANCE XR-500

















































































































Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands

Siemens SCALANCE XR-500, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands