Siemens SCALANCE XR-500 Operating Instructions Manual Download Page 34

Page: 34 / 112

Description of the device

3.4 C-PLUG / KEY-PLUG

SCALANCE XR-500

Operating Instructions, 05/2017, A5E03275845-11

Response to errors

Inserting a C-PLUG/KEY-PLUG that does not contain the configuration of a compatible

device type, accidentally removing the C-PLUG/KEY-PLUG or general malfunctions of the C-

PLUG/KEY-PLUG are signaled by the diagnostics mechanisms of the device (LEDs, Web-

based management (WBM), SNMP, Command Line Interface (CLI) and PROFINET

diagnostics).
The user then has the choice of either removing the C-PLUG/KEY-PLUG again or selecting

the option to reformat the C-PLUG/KEY-PLUG.

3.4.2

Removal and insertion of the C-PLUG/KEY-PLUG

NOTICE
Do not remove or insert a C-PLUG/KEY-PLUG during operation
A C-PLUG/KEY-PLUG may only be removed or inserted when the device is turned off.

Position of the C-PLUG/KEY-PLUG with rack devices

On a SCALANCE XR524-8C and SCALANCE XR526-8C,

the slot is below a cover on the left-hand side of the hous-

ing.
On a SCALANCE XR528-6M and SCALANCE XR552-12M,

the slot is below a cover on the right-hand side of the hous-

ing.
After undoing the screw (screw head Torx T10), you can

remove the cover plate and the slot is accessible.

Removing a C-PLUG/KEY-PLUG

Turn off the power to the device.

Remove the cover.

Insert a screwdriver between the front edge of the C-

PLUG/KEY-PLUG (position A) and the slot and release

the C-PLUG/KEY-PLUG.

Remove the C-PLUG/KEY-PLUG and screw the cover

plate firmly in place again.

Summary of Contents for SCALANCE XR-500

















































































































Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands

Siemens SCALANCE XR-500, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-500

Reviews:

Related manuals for SCALANCE XR-500

Brands by name

Popular brands