Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 57 | Manualshive

Page: 57 / 100

background image

6.5

Power supply 240 VAC

Notes on the power supply

WARNING

Danger from line voltage for devices with a 240 VAC power supply

This device can only function correctly and safely if it is transported, stored, set up, and installed
correctly, and operated and maintained as recommended.

Connecting and disconnecting may only be performed by an electrical specialist.

Connect or disconnect power supply cables only when the power is turned off!

WARNING

Devices with a 240 VAC voltage supply do not have an approval for hazardous areas

Devices with a 240 VAC power supply are not approved for use in hazardous areas according to
ATEX, IECEx, FM and UL HazLoc.

NOTICE
Securing cables with dangerous voltage

Make sure that the connector cannot be released accidentally by pulling on the connecting
cable. Lay the cables in cable ducts or cable channels and secure the cables, where necessary,
with cable ties.

Note
Use in IT networks

When used in IT networks, the power supply 240 VAC also applies to the connected IT network:
Phase-to-phase.

Information on the power supply

• The power supply is connected using an IEC plug C13/C14. The device installation plug C14

is located on the rear panel of the device.

• The device installation plug is three pin with neutral conductor

①

, protective conductor

②

and external conductor

③

.

• The device is grounded via the power cable.

• The power supply is single (1 x 240 VAC).

• To connect the power supply, use the power cable listed in the section "Accessories

Connecting up

6.5 Power supply 240 VAC

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

57

«
...
55
56
57
58
59
...
»

Summary of Contents for SCALANCE XR-300WG





































































































Reviews:

No comments

Related manuals for SCALANCE XR-300WG

DGS-3224TGR - Switch

Brand: D-Link Pages: 160

Brand: D-Link Pages: 145

DGS-1510 Series

Brand: D-Link Pages: 64

DES-3528 - xStack Switch - Stackable

Brand: D-Link Pages: 367

Brand: 6TL Pages: 25

Brand: Datavideo Pages: 38

Brand: 3onedata Pages: 2

Brand: Taiden Pages: 21

Brand: Orei Pages: 27

TPR22-BM Series

Brand: KBT Pages: 4

Brand: Sven Pages: 4

Brand: TCi Pages: 11

Brand: Emos Pages: 44

Brand: IOGear Pages: 54

NSwitch Outdoors

Brand: Moxa Technologies Pages: 30

Brand: Alloy Pages: 64

DVIMUX4-DL-PS/2

Brand: G&D Pages: 40

Brand: SALZ Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands