manualshive.com logo in svg

Siemens SCALANCE XR-300M PoE Series, Compact Operating Instructions

Share
Download
Siemens SCALANCE XR-300M PoE Series Compact Operating Instructions Download Page 34

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD

Replacing components may impair suitability for Class 1, Division 2 or Zone 2.

WARNING

The device is intended for indoor use only.

WARNING

The device may only be operated in an environment of contamination class 1 or 2 (see EN/IEC 
60664-1, GB/T 16935.1).

WARNING

When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone 2, 
the device must be installed in a cabinet or a suitable enclosure.

Notes for use in hazardous locations according to ATEX, IECEx, UKEX and CCC Ex
If you use the device under ATEX, IECEx, UKEX or CCC Ex conditions you must also keep to the 
following safety instructions in addition to the general safety instructions for protection against 
explosion:

5.2

Requirements for the cabinet EN 60529 (ATEX), UKEX, IECEx and 

CCC-Ex

WARNING

To comply with EU Directive 2014/34 EU (ATEX 114), UK-Regulation SI 2016/1107 or the 
conditions of IECEx or CCC-Ex, the housing or cabinet must meet the requirements of at least 
IP54 (according to EN/IEC 60529, GB/T 4208) in compliance with EN IEC/IEC 60079‑7, GB 
3836.8.

Installation and disassembly
5.2 Requirements for the cabinet EN 60529 (ATEX), UKEX, IECEx and CCC-Ex

SCALANCE XR-300M PoE

34

Compact Operating Instructions, 03/2022, A5E02661178-15

Summary of Contents for SCALANCE XR-300M PoE Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands