manualshive.com logo in svg

Siemens SCALANCE XP208EEC, Operating Instructions Manual

Share
Download
Siemens SCALANCE XP208EEC Operating Instructions Manual Download Page 20

Data line

Component

Description

Article number

Connecting cable (M12/RS-232) Preassembled, serial cable with 

M12 and RS-232 plug,
Length: 3 m
pack of 1

6GK5 980-3BC00-0AA5

IE FC TP STANDARD CABLE 
GP2X2
(PROFINET type A)

Standard bus cable, TP installation 
cable for connection to FC OUTLET 
RJ-45, for universal use, 4-wire, 
shielded, CAT 5E
Sold by the meter

6XV1 840-2AH10

IE FC TP ROBUST STANDARD CA‐
BLE GP 2X2
(PROFINET type A)

Standard bus cable, ATPE outer jack‐
et for connection to FC RJ45 PLUG 
and FC OUTLET RJ45, fixed installa‐
tion, for universal use, 4-wire, shiel‐
ded, CAT 5
Sold by the meter

6XV1 841-2A

IE FC TP ROBUST FLEXIBLE CA‐
BLE GP 2X2
(PROFINET type B)

Flexible bus cable, TPE outer jacket 
for connection to FC RJ45 PLUG and 
FC OUTLET RJ45, flexible wires, 4-
wire, shielded, CAT 5
Sold by the meter

6XV1 841-2B

IE FC TP FLEXIBLE CABLE GP 2X2
(PROFINET type B)

Flexible bus cable, TP installation 
cable, flexible wires, shielded, CAT 5
Sold by the meter

6XV1 870-2B

IE FC TP TRAILING CABLE 2X2
(PROFINET type C)

Highly flexible bus cable, TP instal‐
lation cable for connection to FC 
OUTLET RJ45, for use in drag chains, 
4-wire, shielded, CAT 5
Sold by the meter

6XV1 840-3AH10

IE TP TORSION CABLE 2X2
(PROFINET type C)

Highly flexible bus cable, TP instal‐
lation cable for use in highly flexible 
applications (torsion), 4-wire
Sold by the meter

6XV1 870-2F

IE FC TP STANDARD CABLE GP 
4X2

Shielded TP installation cable for 
connection to IE FC RJ45 PLUG 4X2, 
CAT 6, AWG 24
Sold by the meter

6XV1 878-2A

IE FC TP FLEXIBLE CABLE GP 4X2 Shielded TP installation cable for 

connection to IE FC RJ45 PLUG 4X2, 
flexible wires, CAT 6, 24 AWG
Sold by the meter

6XV1 878-2B

IE CONNECTING CABLE 
M12-180/IE RJ45

Flexible IE connecting cable, 4-wire, 
preassembled with a 4-pin M12 
plug (D-coded) and an IE FC RJ-45 
Plug 145

6XV1 871-5T*

IE CONNECTING CABLE 
M12-180/M12-180

Flexible IE connecting cable, 4-wire, 
preassembled with two 4-pin M12 
plugs (D-coded)

6XV1 870-8A*

Description of the device
4.1 Product overview

SCALANCE XP-200

20

Operating Instructions, 03/2021, C79000-G8976-C428-08

Summary of Contents for SCALANCE XP208EEC

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands