Siemens SCALANCE X101-1 Commissioning Manual Download Page 69

Page: 69 / 86

Installation and Maintenance

5.2 Grounding

5.1.3

Wall Mounting

Use four wall plugs (6 mm diameter and 30 mm long).

To attach the device, use screws with a diameter of 3.5 mm and a length of 40 mm.

Note the drilling templates in chapter 8 Dimension Drawings.

Note

The wall mounting must be capable of supporting at least four times the weight of the

device.

5.2

Grounding

Installation on a DIN Rail

The device is grounded over the DIN rail.

S7 DIN Rail

The device is grounded over its rear panel and the neck collar screw.

Wall Mounting

The device is grounded by the securing screw in the unpainted hole.

Please note that the media converter of the SCALANCE X-100 series must be grounded

over one securing screw with minimum resistance.
If a device of the SCALANCE X100 product line is mounted on a non-conducting base, a

grounding cable must be installed. The grounding cable is not supplied with the device.

Connect the paint-free surface of the device to the nearest grounding point using the

grounding cable.

Industrial Ethernet Media Converters SCALANCE X-100 Series
Commissioning Manual, 07/2008, A2B00051521A

5-5

Summary of Contents for SCALANCE X101-1























































































Search results

Summary of Contents for SCALANCE X101-1

Reviews:

Related manuals for SCALANCE X101-1

Brands by name

Popular brands

Siemens SCALANCE X101-1, Commissioning Manual

Search results

Summary of Contents for SCALANCE X101-1

Reviews:

Related manuals for SCALANCE X101-1

Brands by name

Popular brands