Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 9

Page: 9 / 158

Overview of the IE switches SCALANCE X-200RNA

The IE switches SCALANCE X-200RNA are available in different versions. These are listed

in the table below for a better overview:

IE switch

MLFB

Supported modes

SCALANCE X204RNA (PRP)

6GK5204-0BA00-2KB2

PRP ↔ Standard Ethernet
PRP ↔ HSR link

SCALANCE X204RNA (HSR)

6GK5204-0BA00-2MB2

HSR ↔ standard Ethernet;

HSR ↔ PRP link

SCALANCE X204RNA EEC (PRP)

6GK5204-0BS00-3LA3

PRP ↔ Standard Ethernet

SCALANCE X204RNA EEC (HSR)

6GK5204-0BS00-2NA3

HSR ↔ standard Ethernet;

HSR ↔ PRP link

SCALANCE X204RNA EEC (PRP/HSR) 6GK5204-0BS00-3PA3

PRP ↔ standard Ethernet
HSR ↔ standard Ethernet;
HSR ↔ PRP link

Finding information

To help you to find the information you require more quickly, the manual includes not only the

table of contents but also the following sections in the Appendix:
● Index

Audience

These Operating Instructions are intended for persons commissioning Ethernet networks with

the "Parallel Redundancy Protocol" (PRP) and/or "High-availability Seamless Redundancy

Protocol (HSR)".

Standards and approvals

The devices of the SCALANCE X-200RNA product line meet the requirements for the CE mark.

For more detailed information, refer to the section "Approvals and marking (Page 137)" in these

Operating Instructions.

Note
The specified approvals apply only when the corresponding mark is printed on the product.

Industry Online Support

In addition to the product documentation, the comprehensive online information platform of

Siemens Industry Online Support at the following Internet address:

(

http://support.automation.siemens.com/WW/llisapi.dll?

func=cslib.csinfo2&aktprim=99&lang=en

)

Introduction

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

Summary of Contents for SCALANCE X-200RNA































































































































































Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Related manuals for SCALANCE X-200RNA

Brands by name

Popular brands

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Related manuals for SCALANCE X-200RNA

Brands by name

Popular brands