Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 139

Page: 139 / 158

The product meets the requirements of the standards
● EN 60079-15 (electrical apparatus for potentially explosive atmospheres; Type of protection

"n")

● and EN 60079-0

FM approval

The devices of the type SCALANCE X204RNA meet the requirements of standards:
● Factory Mutual Approval Standard Class Number 3611
● FM Hazardous (Classified) Location Electrical Equipment:

Non Incendive / Class I / Division 2 / Groups A,B,C,D / T4 A and

Non Incendive / Class I / Zone 2 / Group IIC / T4

FDA and IEC approvals

The following products meet the FDA and IEC requirements listed below.
● SFP module SFP991-1LD
● SFP module SFP991-1LH+

Figure 8-1

FDA and IEC approvals

Notice for Australia (C-Tick)

The product meets the requirements of the AS/NZS 2064 standard (Class A).

Notice for Korea (Kc)

The product meets the requirements of the Korea Certification.

UL Approval for Information Technology Equipment

Underwriters Laboratories (UL) complying with Standard UL 60950-1

UL Approval for Industrial Control Equipment

Underwriters Laboratories (UL) complying with Standard UL 508

Approvals and marking

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

139

Summary of Contents for SCALANCE X-200RNA































































































































































Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Related manuals for SCALANCE X-200RNA

Brands by name

Popular brands

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Related manuals for SCALANCE X-200RNA

Brands by name

Popular brands