manualshive.com logo in svg

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Share
Download
Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 129

● 512 - 1023 bytes
● 1024 - 1536 bytes

Figure 7-41 Packet Size Statistic Graphic 

With the check box in the "Packet Size" column, you decide the content of the graphic. The 

value in the "Packets" column in the graphic is only displayed for a certain range if the 

appropriate check box is selected. The "Percentage" column shows the packets in a certain 

length range as a percentage of the total packets for this port. When the percentage is 

calculated, ranges are included only if their check boxes are selected.
With the "Previous Port" and "Next Port" buttons, you can change to the display of the previous 

or next port.

7.10.7

Packet Type Statistic

Received frames sorted by type

The "Packet Type Statistic" dialog box displays how many frames of the type unicast, multicast, 

and broadcast were received and sent at each port.

Functional description and configuration using Web Based Management

7.10 The "Switch" menu

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

129

Summary of Contents for SCALANCE X-200RNA































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands