Siemens SCALANCE X-100 Operating Instructions Manual Download Page 5

Page: 5 / 78

SCALANCE X-100
Operating Instructions, 12/2016, A2B00060666-08

Introduction

1.1

On the Operating Instructions

Purpose of the Operating Instructions

These Operating Instructions support you when commissioning networks with the Industrial

Ethernet switches of the SCALANCE X-100 product line.

Validity of the Operating Instructions

These operating instructions are valid for the following devices:

Device

Order number

SCALANCE X104-2

6GK5 104-2BB00-2AA3

SCALANCE X106-1

6GK5 106-1BB00-2AA3

SCALANCE X108

6GK5 108-0BA00-2AA3

SCALANCE X108PoE

6GK5 108-0PA00-2AA3

SCALANCE X112-2

6GK5 112-2BB00-2AA3

SCALANCE X116

6GK5 116-0BA00-2AA3

SCALANCE X124

6GK5 124-0BA00-2AA3

Further documentation

The "SIMATIC NET Industrial Ethernet Twisted Pair and Fiber Optic Networks" manual

contains additional information on other SIMATIC NET products that you can operate along

with the IE switches of the SCALANCE XB-000 product line in an Industrial Ethernet

network.
You can order the manual "SIMATIC NET Industrial Twisted Pair and Fiber Optic Networks",

release 05/2001, using the following order numbers:

6GK1970-1BA10-0AA0 German

6GK1970-1BA10-0AA1 English

6GK1970-1BA10-0AA2 French

6GK1970-1BA10-0AA4 Italian
You will also find this network manual on the Internet pages of Service & Support under the

following entry ID: 1172207 (

http://support.automation.siemens.com/WW/view/en/1172207

You will find further information in the "System Manual Industrial Ethernet" in the Manual

Collection.
You will find further information on the SCALANCE system on the Internet at

www.siemens.com/scalance (

www.siemens.com/scalance

You can obtain the "PROFINET Installation Guide" from the PROFIBUS User Organization

(PNO).

Summary of Contents for SCALANCE X-100















































































Search results

Summary of Contents for SCALANCE X-100

Reviews:

Brands by name

Popular brands

Siemens SCALANCE X-100, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X-100

Reviews:

Brands by name

Popular brands