Siemens SCALANCE W788C-2 Operating Instructions Manual Download Page 18

Page: 18 / 50

Description

3.4 Accessories

SCALANCE W788C-2

Operating Instructions, 07/2019, A5E03692120-14

Flexible connecting cable N-Connect/N-Connect

Flexible connecting cable for connecting an antenna to a SCALANCE W device with N-

Connect connectors.

Preassembled with two N male connectors:

Length

Article number

1 m

6XV1875-5AH10

2 m

6XV1875-5AH20

5 m

6XV1875-5AH50

10 m

6XV1875-5AN10

For railway applications, the following connecting cable are available:

Length

Article number

1 m

6XV1875-5SH10

2 m

6XV1875-5SH20

5 m

6XV1875-5SH50

Flexible connecting cable IWLAN QMA/N-Connect male/female

Adapter cable for connecting a MIMO antenna with QMA connectors with the flexible

connecting cables. Preassembled with two connectors QMA male and N-Connect female.

pack of 3

Length

Article number

1 m

6XV1875-5JH10

For railway applications, the following connecting cable is available Note: Scope of delivery:

Pack of 1

Length

Article number

1 m

6XV1875-5VH10

3.4.1.2

Antennas

Note
When you select an antenna, keep in mind the national approvals for your device.
You can find additional information under Wireless approvals

(

https://www.siemens.com/wireless-approvals

)

The SCALANCE W786C-2IA RJ-45 uses internal omni antennas (3/4 dBi at 2.4 GHz or 5

GHz).

Summary of Contents for SCALANCE W788C-2



















































Search results

Summary of Contents for SCALANCE W788C-2

Reviews:

Related manuals for SCALANCE W788C-2

Brands by name

Popular brands

Siemens SCALANCE W788C-2, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE W788C-2

Reviews:

Related manuals for SCALANCE W788C-2

Brands by name

Popular brands