Siemens SCALANCE W786-x Operating Instructions Manual Download

Page: 59 / 68

SCALANCE W786-x
Operating Instructions, 11/2014, A5E03678337-07

Technical specifications

Product versions

The technical specifications of the product variants of the SCALANCE W786 are largely

identical. Unless indicated otherwise in the table, the following tables apply to all W786

product variants:

Data transfer
Ethernet transfer rate

1 Gbps

Wireless transmission rate

1 ... 450 Mbps

Wireless standards supported

IEEE 802.11a

IEEE 802.11b

IEEE 802.11g

IEEE 802.11h

IEEE 802.11n

Power supply standards supported

IEEE 802.3at type 2, IEEE 802.3af (IEEE 802.3at type 1)

Note
You will find detailed information on the transmit power and receiver sensitivity in the

document "Leistungsdaten 802.11abgn PCIe Minicard / Characteristics 802.11abgn PCIe

Minicard" (REF_W700-RadioInterface_74.pdf).

Interfaces
Power

Direct power supply 24 VDC

min. 19.2 VDC, max. 28.8 VDC via supplied connector,

not electrically isolating.
Power over Ethernet 50 VDC

min. 36 VDC, max. 57 VDC via RJ-45 jack, electrically

isolated according to IEEE802.3at, dielectric resistance >

2 Mohms.
12 to 24 VDC

min. 9.6 VDC, max. 28.8 VDC via optional power supply

adapter
100 to 240 VAC

via optional power supply adapter

Summary of Contents for SCALANCE W786-x





































































Search results

Summary of Contents for SCALANCE W786-x

Reviews:

Related manuals for SCALANCE W786-x

Brands by name

Popular brands

Siemens SCALANCE W786-x, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE W786-x

Reviews:

Related manuals for SCALANCE W786-x

Brands by name

Popular brands