Siemens SCALANCE M812 Operating Instructions Manual Download Page 65 | Manualshive

Page: 65 / 74

Siemens SCALANCE M812 Operating Instructions Manual Download Page 65

Approvals

9

Approvals issued

Note
Issued approvals on the type plate of the device

The specified approvals apply only when the corresponding mark is printed on the product. You
can check which of the following approvals have been granted for your product by the markings
on the type plate.

Current approvals on the Internet

You will find the current approvals for the product on the Internet pages of Siemens Industry
Online Support at the following link: (

https://support.industry.siemens.com/cs/ww/en/ps/

)

Installation guidelines

The devices meet the requirements if you adhere to the installation and safety instructions
contained in this documentation and in the following documentation when installing and
operating the devices.

• "Industrial Ethernet / PROFINET Industrial Ethernet" System Manual (

support.industry.siemens.com/cs/ww/en/view/27069465

• "Industrial Ethernet / PROFINET - Passive Network Components" System Manual (

support.industry.siemens.com/cs/ww/en/view/84922825

• "EMC Installation Guidelines" configuration manual (

support.industry.siemens.com/cs/ww/en/view/60612658

WARNING

Personal injury and property damage can occur

The installation of expansions that are not approved for products or their target systems may
violate the requirements and regulations for safety and electromagnetic compatibility.

Only use expansions that are approved for the system.

SCALANCE M826
Operating Instructions, 10/2022, C79000-G8976-C362-07

65

«
...
63
64
65
66
67
...
»

Summary of Contents for SCALANCE M812











































































Reviews:

No comments