manualshive.com logo in svg

Siemens SCALANCE M812, Operating Instructions Manual, Page: 59 / 74

Share
Download
Siemens SCALANCE M812 Operating Instructions Manual Download Page 59

Technical specifications

7

  SCALANCE M826-2 

Article number

6GK5 826-2AB00-2AB2

Ethernet interface
Attachment to Industrial Ether‐
net

Quantity

4

 

Design
 

RJ-45 jack
Characteristics: 
• 10/100BASE-T
• Ethernet IEEE 802
• 10/100 Mbps

WAN interface
DSL connection
 
 

Quantity

2

Design

Terminal block, 2 terminals

G.SHDSL
G.SHDSL.bis

Properties

ITU-T G.991.2.bis

Transmission speed

2-wire mode: up to 15.3 Mbps
4-wire mode (aggregated): up to 30 Mbps

Electrical data
Power supply

Input voltage

12 to 24 VDC
min. 10.8 VDC, max. 28.8 V 

Maximum power con‐
sumption

7 W

Digital input

Quantity

1

Design

Terminal block, 2 terminals

Characteristics:

Rated voltage 24 VDC Safe Extra Low Volt‐
age (SELV)
For state "1": 13 to 30 VDC
For state "0": -30 to 3 VDC
Maximum input current 8 mA
Cables should be routed in pairs
Maximum cable length < 30 m
Inputs isolated from electronics.

SCALANCE M826
Operating Instructions, 10/2022, C79000-G8976-C362-07

59

Summary of Contents for SCALANCE M812











































































Reviews:

No comments