manualshive.com logo in svg

Siemens SCALANCE M804PB, Operating Instructions Manual

Share
Download
Siemens SCALANCE M804PB Operating Instructions Manual Download Page 37

 

SCALANCE M804PB 
Operating Instructions, 07/2018, C79000-G8976-C496-01 

37

 

 

Connecting up 

5 

5.1

 

Safety when connecting up 

Safety notices 

When connecting up the device, keep to the safety notices listed below. 

 

 

WARNING 

EXPLOSION HAZARD 
SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 

2 OR ZONE 2. 

 
 

 

WARNING 

EXPLOSION HAZARD 
DO NOT OPEN WHEN ENERGIZED. 

 

 

 

Note 
Strain relief for the Ethernet cables 
In order to avoid mechanical stress on the Ethernet cables and resulting interruption of the 

contact, fasten the cables at a short distance from the connector using a cable guide or 

busbar. 

 

 

 

WARNING 

The equipment is designed for operation with Safety Extra-Low Voltage (SELV) by a 

Limited Power Source (LPS). 
This means that only SELV / LPS complying with IEC 60950-1 / EN 60950-1 / VDE 0805-1 

must be connected to the power supply terminals. The power supply unit for the equipment 

power supply must comply with NEC Class 2, as described by the National Electrical Code 

(r) (ANSI / NFPA 70). 
If the equipment is connected to a redundant power supply (two separate power supplies), 

both must meet these requirements. 

 

Summary of Contents for SCALANCE M804PB





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands