Siemens SAB 80515 Series User Manual Download Page 75 | Manualshive

Page: 75 / 270

Siemens SAB 80515 Series User Manual Download Page 75

Semiconductor Group

75

On-Chip Peripheral Components

Table 7-6
Selection of the Analog Input Channels

The bits MX0 to MX2 in special function register ADCON are used for selection of the analog input
channels.

Port 6 of the ACMOS versions is a dual purpose input port. lf the input voltage meets the specified
logic levels, it can be used as digital input as well regardless of whether the pin levels are sampled
by the A/D converter at the same time.

The special function register ADDAT (figure 7-28) holds the converted digital 8-bit data result. The
data remains in ADDAT until it is overwritten by the next converted data. ADDAT can be read or
written under software control. lf the A/D converter of the SAB 80(C)515 is not used, register
ADDAT can be used as an additional general purpose register.

Figure 7-28
Special Function Register ADDAT (Address 0D9H)

This register contains the 8-bit conversion result.

7.4.1.2 Start of Conversion

An internal start of conversion is triggered by a write-to-DAPR instruction. The start procedure itself
is independent of the value which is written to DAPR. However, the value in DAPR determines
which internal reference voltages are used for the conversion (see section 7.4.2).

When single conversion mode is selected (ADM = 0) only one conversion is performed. In
continuous mode after completion of a conversion a new conversion is triggered automatically, until
bit ADM is reset.

MX2

MX1

MX0

Selected Channel

Pin

MYMOS

ACMOS

0

0

0

Analog input 0

AN0

P6.0

0

0

1

Analog input 1

AN1

P6.1

0

1

0

Analog input 2

AN2

P6.2

0

1

1

Analog input 3

AN3

P6.3

1

0

0

Analog input 4

AN4

P6.4

1

0

1

Analog input 5

AN5

P6.5

1

1

0

Analog input 6

AN6

P6.6

1

1

1

Analog input 7

AN7

P6.7

Conversion result

ADDAT

0D9H

*

«
...
73
74
75
76
77
...
»

Summary of Contents for SAB 80515 Series















































































































































































































































































Reviews:

No comments