Siemens RUGGEDCOM RX1000 Installation Manual Download Page 8 | Manualshive

Page: 8 / 50

background image

Chapter 1

Introduction

RUGGEDCOM RX1000

Installation Guide

2

Feature Highlights

▪ Exceeds IEC 61000-6-2 (generic industrial environment)
▪ Exceeds NEMA TS-2 (traffic control equipment)

• -40 to 85 °C (-40 to 185 °F) operating temperature (no fans)
• Failsafe output relay: for crtical failure or error alarming
• 18 AWG galvanized steel enclosure and 48 cm (19 in) rack-mount adapter

Universal Power Supply Options

• Fully integrated power supplies
• Input voltage range of 10-59 VDC, 88-300 VDC or 85-264 VAC for worldwide operability
• Optional dual redundant, parallel load-sharing power supplies for increased network availability
• Can be powered from different sources for ultimate redundancy
• CSA/UL 60950-1 safety approved to 85 °C (185 °F)

Physical Ports

• Ethernet Options (up to 4 ports): 10/100Base-TX, 100Base-FX
• Cellular Modem
• WAN Port Options (up to 8 ports):

▪ T1/E1 (channelized/unchannelized) supports 2 Mbps G.703 with 120 Ω balanced connections
▪ PPPoE/Bridged Ethernet via ADSL
▪ T3 DS3
▪ 56 Kbps DDS

• Serial Ports (up to 8 ports):

▪ Fully compliant EIA/TIA RS485, RS422, RS232 software selectable serial ports with RJ45 connectors
▪ Raw socket mode support allows conversion of any serial protocol

• Embedded Modem Port
• Precision Time Protocol (PTP): Accurate time synchronization using NTP, IRIG-B and/or IEEE1588

Protocols

• WAN

▪ Frame Relay RFC 1490 or RFC 1294
▪ PPP RFC 1661, 1332, 1321, 1334, PAP, CHAP Authentication
▪ PPPoE over DSL
▪ GOOSE messaging support

• IP

▪ Routing: VRRP, OSPF, RIP, BGP
▪ DHCP Agent (Option 82 capable)
▪ Traffic prioritization, NTP Server, IP Multicast Routing

Frame Relay Support

• ISO and ITU compliant, network certified
• ANSI T1.617 Annex D, Q.933 or LMI Local Signalling

«
...
6
7
8
9
10
...
»

Summary of Contents for RUGGEDCOM RX1000



















































Reviews:

No comments

Related manuals for RUGGEDCOM RX1000

Brand: D-Link Pages: 13

Brand: GE Pages: 6

Brand: TP-Link Pages: 2

BroadLink SP3353

Brand: MicroNet Pages: 66

Brand: iBall Baton Pages: 9

RUGGEDMAX WIN7000

Brand: RuggedCom Pages: 42

Wisenet PRN-6400B4

Brand: Hanwha Techwin Pages: 14

SmartMesh IA-510 D2511

Brand: Dust Networks Pages: 30

Brand: Draytek Pages: 2

Brand: Genie Pages: 6

Brand: QUNDIS Pages: 42

Brand: Digisol Pages: 81

Brand: US Robotics Pages: 180

Brand: Xantech Pages: 6

Brand: KYLAND Technology Pages: 19

Brand: LevelOne Pages: 83

DUAL Nx56/64 1200142L1#

Brand: ADTRAN Pages: 48

GigaSpire BLAST u4hm

Brand: Calix Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands