background image

Chapter 6

Certification

RUGGEDCOM RS920W

Installation Guide

30

FCC

CAN/CSA-C22.2 No. 142-M1987

Process Control Equipment Industrial Products

CAN/CSA-C22.2 No. 213-16

Non-Incendive Electrical Equipment for Use in Class I and II, Division 2 and Class III, Divisions 1 and 2 Hazardous

(Classified) Locations (Bi-National Standard with ANSI/ISA-12.12.01-2016)

UL 916

Standard for Energy Management Equipment

ANSI/ISA-12.12.01-2015

Non-Incendive Electrical Equipment for Use in Class I and II, Division 2 and Class III, Division 1 and 2 Hazardous

(Classified) Locations

It is specifically approved for use in hazardous locations with the following markings:
• Class I, Division 2, Groups A, B, C, D
• Temperature rating T6 at 40 °C and T4A at 85 °C

Section 6.1.2

FCC

This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment.
This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case users will be required to

correct the interference at their own expense.

IMPORTANT!

Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate this device.

Section 6.1.3

FDA/CDRH

This device meets the requirements of the following U.S. Food and Drug Administration (FDA) standard:
• Title 21 Code of Federal Regulations (CFR) – Chapter I – Sub-chapter J – Radiological Health

Section 6.1.4

ISED

This device is declared by Siemens Canada Ltd to meet the requirements of the following ISED (Innovation Science

and Economic Development Canada) standard:
• CAN ICES-3 (A)/NMB-3 (A)

Summary of Contents for RUGGEDCOM RS920W













































Reviews: