manualshive.com logo in svg

Siemens RUGGEDCOM RS920W, Installation Manual, Page: 19 / 44

Share
Download
Siemens RUGGEDCOM RS920W Installation Manual Download Page 19

RUGGEDCOM RS920W

Installation Guide

Chapter 2

Installing the Device

Connecting the Failsafe Alarm Relay

9

2

1

2

1

Figure 3: Panel Mounting

1.

 Screw   

 

2.

 Panel Mount Adapter

3. Secure the adapters to the panel with #6-32 screws.

Section 2.5

Connecting the Failsafe Alarm Relay

The failsafe relay can be configured to latch based on alarm conditions. The NO (Normally Open) contact is closed

when the unit is powered and there are no active alarms. If the device is not powered or if an active alarm is

configured, the relay opens the NO contact and closes the NC (Normally Closed) contact.

NOTE

Control of the failsafe relay output is configurable through ROS. One common application for this relay

is to signal an alarm if a power failure occurs. For more information, refer to the ROS User Guide for

the RUGGEDCOM RS920W.

To connect the failsafe alarm relay, do the following:
1. Insert the failsafe alarm relay terminal block into the device and tighten the screws.
2. Connect a failsafe device to the terminal block.

Summary of Contents for RUGGEDCOM RS920W













































Reviews:

No comments