Chapter 6
Security
RUGGEDCOM ROX II
CLI User Guide
126
Enabling and Configuring SFTP Sessions
Parameter
Description
Additional IPv4 or IPv6 addresses and their associated ports on which the CLI will listen
for requests from the device. IPv4 addresses and port numbers must be separated by a
colon (e.g. 192.168.0.2: 19343). IPv6 addresses and port numbers must be separated by
square brackets and a colon (e.g. [2001:db8:2728::2200]:[19343]).
If the Listen IP (listen-ip) parameter is set to a value other than 0.0.0.0, the port specified
by the Listen Port (port) parameter must not be associated with any additional addresses.
max-sessions { max-sessions }
Synopsis:
a 32-bit unsigned integer
Default:
10
The maximum number of concurrent CLI sessions.
idle-timeout { idle-timeout }
Synopsis:
A string
Default:
PT30M
The maximum period of time that a CLI session may remain idle. After this period
of time, the session is terminated. Values are expressed in durations of years,
months, weeks, days, hours, minutes, and/or seconds in ISO 8601 format (e.g.
P1Y1M2W3DT2H3M30S corresponds with 1 year, 1 month, 2 weeks, 3 days, 2 hours, 3
minutes, and 30 seconds).
A session is not considered idle if the CLI is waiting for notifications or if commits are
pending. If the value of this parameter is changed during a session, the change will not
take effect until the next session.
greeting { greeting }
Synopsis:
A string 1 to 8192 characters long
A greeting message presented to users when they log in to the CLI. The message must be
enclosed in quotation marks.
3. Type
commit
and press
Enter
to save the changes, or type
revert
and press
Enter
to abort.
Section 6.2
Enabling and Configuring SFTP Sessions
To enable and configure SFTP sessions, do the following:
1. Make sure the CLI is in Configuration mode.
2. Navigate to
admin
and configure the following parameter(s) as required:
Parameter
Description
enabled
Synopsis:
{ true, false }
Default:
false
Enables/Disables the SFTP user interface.
listen-ip { listen-ip }
Synopsis:
A string
Default:
0.0.0.0
The IP Address the SFTP will listen on for SFTP requests.
port { port }
Synopsis:
A 16-bit unsigned integer between 0 and 65535
Default:
2222
The port the SFTP will listen on for SFTP requests.
extra-ip-ports { extra-ip-ports }
Synopsis:
A string
The SFTP will also listen on these IP Addresses. For port values, add ':#' to set non-default
port value. (ie. xxx.xxx.xxx.xxx:19343 [::] [::]:16000). If using the default address, do not
specify another listen address with the same port.
max-sessions { max-sessions }
Synopsis:
a 32-bit unsigned integer
Summary of Contents for RUGGEDCOM ROX II
