Siemens RUGGEDCOM M969F Installation Manual Download Page 28 | Manualshive

Page: 28 / 56

background image

Chapter 3

Device Management

RUGGEDCOM M969F

Installation Guide

18

Configuring the Device

Communication Ports

Connect any of the available Ethernet ports on the device to a management switch and access the ROS console

and Web interfaces via the device's IP address. The factory default IP address for the RUGGEDCOM M969F is

https://192.168.0.1

.

For more information about available ports, refer to

Communication Ports

Section 3.2

Configuring the Device

Once the device is installed and connected to the network, it must be configured. All configuration management

is done via the RUGGEDCOM ROS interface. For more information about configuring the device, refer to the

RUGGEDCOM ROS User Guide

associated with the installed software release.

«
...
26
27
28
29
30
...
»

Summary of Contents for RUGGEDCOM M969F

























































Reviews:

No comments

Related manuals for RUGGEDCOM M969F

Brand: Dataprobe Pages: 31

Brand: IBM Pages: 13

Flex System EN2092

Brand: IBM Pages: 2

Brand: 3Com Pages: 8

Brand: AbleNet Pages: 2

Brand: Abtus Pages: 15

Crouse-Hinds CEAG KO

Brand: Cooper Pages: 12

Brand: Linksys Pages: 3

Brand: SMART Pages: 46

Sierra Video 1208V3S

Brand: Kramer Pages: 2

Brand: hager Pages: 2

Brand: HIKVISION Pages: 25

Brand: CYP Pages: 28

Brand: Optex Pages: 2

Brand: Hall Research Technologies Pages: 9

MaxiiNet VI3026

Brand: Vigitron Pages: 288

Brand: Omega Pages: 17

Brand: National Instruments Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands