background image

 

 

Installation Instructions 

Document No. 129-116  

September 24, 2009

 

 

TH 192 Pneumatic Room Thermostat 
Retrostat Kits 

 

 

Item Number 129-116, Rev. FA

 

Page 1 of 12 

Product Description 

The TH 192 Pneumatic Room Thermostat Retrostat 
kits convert most existing pneumatic room 
thermostats to a Powers™ Controls TH 192 direct or 
reverse acting, two-pipe, single setpoint device. This 
kit includes a cover that can be configured to 
conceal or expose the setpoint adjustments, setpoint 
indicator, and thermometer. Also, the kits can 
include an optional 1/2-inch large, exposed setpoint 
adjustment knob.  

Contents 

Part 

Quantity 

Retrostat Cover Kit 

Thermostat * 

Hardware kit  

Optional 1/2-Inch Large, Exposed 
Setpoint Knob  

Adapter Frame (192-308) 

*  Includes thermostat installation instructions.  

Product Numbers 

Retrostat Kit  

(See Notes below) 

Type 

192-840 

Direct Acting Fahrenheit Scale 

192-841 

Reverse Acting Fahrenheit Scale 

192-850 

Direct Acting Celsius Scale 

192-851 

Reverse Acting Celsius Scale 

NOTES: 

1.  Includes all parts needed for all conversions 

listed in Table 1 including installations where a 
large rough-in hole must be covered. These 
installations may require an adapter frame 
(192-308). 

2.  For Retrostat Kits with white cover, order the 

standard kit with “W” suffix.  

3.  For Retrostat Kits with optional 1/2-inch large, 

exposed setpoint adjustment knob, order the 
standard kit with “K” suffix.  

Required Tools 

 

Calibration and cover screw wrench 
(192-632) or 1/16” Allen wrench and 1/8” 
open-end wrench 

 

Medium flat-blade screwdriver 

 

Small level 

 

Accurate thermometer 

 

Needle nose pliers  

 

Prerequisites  

 

Review all of these instructions before you 
begin installation.  

 

Check job drawings for any site-specific 
information.  

 

Verify that the existing thermostat installation 
has its supply and return air lines connected 
properly.  

 

Make certain air supply is 18 to 25 psi 
(124 to 172 kPa) normal. 

 

Obtain the installation instructions provided 
with the thermostat in the Retrostat Kit. The 
document provides instructions for calibrating 
the thermostat.  

 

Make certain a supply of wall anchors and 
plastic ties are available.  

Expected Installation Time 

1 hour 

Summary of Contents for Retroline TH 192













Reviews: