manualshive.com logo in svg

Siemens POWERMOBIL, Manual, Page: 28 / 36

Share
Download
Siemens POWERMOBIL Manual Download Page 28

POWERMOBIL

 

SPR2-240.841.01

Page 8 of 10

Siemens AG

 

Rev. 01

05.03

CS PS 24

Medical Solutions

3 - 8

Installation

 

I.I. mini voltage supply and X-ray image intensifier

3

•

Connect the Lemosa plug connector in the C-arm. Insert the plug connector into the 
C-arm. Run the cable in the C-arm so that it is positioned at the side underneath the met-
al cover (1/Fig. 19).

•

Insert the control and high-voltage sections of the I.I. mini voltage supply in the C-arm.

•

Plug in the connection cable (ribbon cable) between control section and high-voltage 
section.

•

Attach the X-ray image intensifier in the (suspended) service position.

•

Fasten the ground wire connections to the image intensifier.

•

Connect the high-voltage cable as well as the cables E1, E2 and E3.

•

Connect the black cathode cable of the X-ray image intensifier to the CON1.8 plug.

•

Connect the CON1 plug to the control section.

•

Attach the camera plug M4 X1 to the mounting bracket.

•

Connect the plug M30 X1.

•

Fasten all cables using cable ties.

•

Lift the X-ray image intensifier, and carefully thread in the cables. Guide the high-voltage 
cable, the cable E3 and the protective ground wire through the bracket (1/Fig. 20). 
Insert the ribbon cable between control section and HV section of the I.I. mini voltage 
supply, at the side between the metal cover (1/Fig. 19) and the C-arm.

•

Fasten the image intensifier.

Fig. 19

Fig. 20

To avoid blocking camera rotation after fastening the X-ray image 
intensifier make sure that all cables are run carefully during 
installation.

NOTE

Summary of Contents for POWERMOBIL





































Reviews:

No comments