Siemens POWERMOBIL SP Maintenance Instruction Download

Page: 29 / 44

Siemens AG

SPR2-240.831.01.02.02

POWERMOBIL

07.05

CS PS 24

Safety Inspection

Page 29 of 44

Medical Solutions

•

Release the orbital brake. The LED in the button goes on.

•

The servo support of the orbital movement must not operate. The C-arm may move in
the orbital direction only when increased force is exerted.

•

Press the Emergency Stop switch. The lifting column can be moved again.

•

Release the orbital brake.

•

The servo support function of the orbital movement is functional once again.. The
C-arm may move in the orbital direction with minimal force.

3.1.1

I.I. laser light localizer

SIM

Mechanical system

•

Inspect the I.I. laser light localizer for mechanical damage.

•

Mount the I.I. laser light localizer on the I.I. and ensure proper locking and seating.
When doing this, pay special attention to the tension band and its closure.

•

Check the I.I. ring for damage.

SIM

Function

•

Perform maintenance on the I.I. laser light localizer according to Installation and Set-
ting Instructions RXR2-130.033.03...

3.1.2 DICOM

bridge

SIM

Mounting

•

Check the mounting of the DICOM bridge in the monitor trolley.

3.1.3 Codonics

printer

SIM

Mounting

•

Inspect the screws used to fasten the guide rail to the mounting bracket of the
Framegrabber.

•

Ensure that the printer is properly fastened to the guide rail. Make sure there are no
missing attachment screws.

•

Ensure that the Framegrabber is properly fastened to the mounting bracket. Make sure
there are no missing attachment screws.

SIM

Guide rails

•

Inspect the guide rails for proper function and smooth operation.

•

The guide rails must not be damaged.

•

The guide rails must lock properly into place when fully pushed into position.

•

If necessary, use a cleaning brush to remove dirt from the rails.

3.1.4 Monitors/displays

SIM

Monitor/displays

Summary of Contents for POWERMOBIL SP













































Search results

Summary of Contents for POWERMOBIL SP

Reviews:

Related manuals for POWERMOBIL SP

Brands by name

Popular brands

Siemens POWERMOBIL SP, Maintenance Instruction

Search results

Summary of Contents for POWERMOBIL SP

Reviews:

Related manuals for POWERMOBIL SP

Brands by name

Popular brands