Siemens OZW775 Basic Documentation Download Page 75 | Manualshive

Page: 75 / 120

background image

75/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Communication via zone addresses

30.08.2007

7.3.2

RXB/RXL room controllers

•

In ACS Service

Applications > Parameter settings

, open the menu tree of the

RXB/RXL room controller for which the zone address is to be set.

•

Double-click the menu line "Communication" to open the operating page, and

select the zone for which the address is to be set. Double-click to open the
dialog box for entry of the address.

•

Enter the zone address and click

OK

to confirm the value entered.

7.3.3 Zone

addressing

with

the QAX34.3 room unit

With the RXB/RXL room controllers, the zone addresses can also be set with the
QAX34.3 room unit (Minor parameterization, see section 5.6.1).

P008 Geographical zone (apartment)

1…126 -1 = Default value

P009 Geographical zone (room)

0…63

1 = Default value

P010 Geographical zone (subzone)

0…15

1 = Default value

P011 Time-switch zone (apartment)

1…126

1 = Default value

P012 Time-switch zone (room)

0…63

1 = Default value

P013 Time-switch zone (subzone)

0…15

1 = Default value

P014 Heat distribution zone, air heater

1…31

-1 = Default value

P015 Refrig distrib. zone, cooling coil

1…31

-1 = Default value

P016 Heat distr zone heating surface.

1…31

-1 = Default value

P017 Refrig distr zone cooling surface

1…31

-1 = Default value

P018 Outside temperature zone

1…31

1 = Default value

P023 Master/slave zone (group)

1…126

1 = Default value

P023 Master/slave zone (room)

0…63

-1 = Default value

P024 Master/slave zone (subzone)

0…15

1 = Default value

"P008" indicates that the "Geographical zone (apartment)" in the RXB/RXL room
controllers is parameter no. 008. For more information, refer to document
CM110385.

For the RM… controllers, the default value in the QAX34.3 room unit is "-1" rather
than "----". Both default values indicate that the zone is "out of service" and that no
process values are transmitted within the zone.

Minor parameterization

Parameter numbers and
associated zones

Notes

«
...
73
74
75
76
77
...
»

Summary of Contents for OZW775

























































































































Reviews:

No comments

Related manuals for OZW775

Brand: Xtrons Pages: 30

Brand: Linak Pages: 33

Brand: PURE Pages: 88

Brand: Carel Pages: 2

Brand: SainSmart Pages: 49

Brand: Grandstream Networks Pages: 12

BeoSound 3000 2671

Brand: Bang & Olufsen Pages: 68

Brand: 2VV Pages: 29

ConferenceSHOT AV

Brand: VADDIO Pages: 34

Brand: CAME BPT Pages: 8

Brand: Ziton Pages: 2

Brand: SKF Pages: 63

Brand: i4Technology Pages: 6

Brand: Champion Pages: 46

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands