Siemens OZW775 Basic Documentation Download Page 72

Page: 72 / 120

72/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Communication via zone addresses

30.08.2007

7.2

Zone addressing with the RMZ operator units

7.2.1

RM… controllers

For the Synco 700 type RM… controllers, the zone addresses can be set with the
RMZ790 and RMZ791 operator units. The zone addresses can be set without a
commissioning tool, also referred to as "Easy configuration".

Access at the Password level takes the user to the operating pages and
operating lines.

To set the zone address, use the following path to the "Room" operating page:

Main menu > Commissioning > Communication > Room

Turn the rotary knob to select the "Geogr zone (apartm)" line.

Turn the knob as required for access to setting mode.

In setting mode, set the zone address rotating the knob as required.

Introduction

Setting procedure

Step 1

RM…controllers

RM…B controllers

Step 2

RM…controllers

RM…B controllers

Step 3

Room

Geogr. zone (ap.): 1

Time switch op: Autonom

TS slave (apart.): 1

Geographical zone (apartment)

126

└┴┴┴┴┴┴┴┴┴┴┴┴┴┴┴┴┘

Geographical zone (apartment)

126

└┴┴┴┴┴┴┴┴┴┴┴┴┴┴┴┴┘

Room

Geogr. zone (ap.): ----

TS slave (apart.): ----

Time switch op: Autonom

Geographical zone (apartment)

----

126

└┴┴┴┴┴┴┴┴┴┴┴┴┴┴┴┴┘

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands