Siemens OZW775 Basic Documentation Download Page 58

Page: 58 / 120

58/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Device addresses via ACS

30.08.2007

7. In ACS Service click

Plant > Refresh device list

to initiate the automatic adoption of

the new line address 11 by the Synco devices.

8. In ACS Service select

Plant > Edit device list…

to open the "Edit device list" dialog

box.

9. Check that the Synco devices are now using the new line address 11.

5.9.2 Area

couplers

The area address (syntax

0 from

0 to

15.

0) can be set in "Programming

mode" via ACS Service in the same way as for the line coupler.

In principle the method is the same as for the line coupler (see Steps 1 to 9 above).

Note:

•

Area couplers are always the highest-level elements in a network. Area

addresses can never be adopted automatically.

•

For area couplers, the line address and device address is always 0.

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands