Siemens OZW775 Basic Documentation Download Page 56 | Manualshive

Page: 56 / 120

background image

56/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Device addresses via ACS

30.08.2007

5.9 Addressing

the

couplers

5.9.1 Line

couplers

The area and line addresses for the area/line couplers can be set with "ACS
Service 7.0 SP1" (SP1 = Service Pack 1).

If ACS Service 7.0 SP1 (or a later version) is unavailable, the area and line
addresses can be set only via ETS.

In technical terms, the coupler devices are identical. Whether they operate as area
couplers or line couplers is determined by the addressing process.

•

Area coupler

Ac

A.

0

.

0

1.

0

.

0 to

15.

0

.

0

•

Line couplers

Lc

X

.L.

0

1

.1.

0 to 15

.15.

0

In the case of the Synco bus devices, only the device address needs to be set. The
Synco bus devices adopt the area and line address dynamically from the area and
line couplers.

Area and line addresses can be set with the coupler concerned in programming
mode.

Only one coupler at a time should be set to programming mode.

To switch the coupler to programming mode, press the learning button A5
("learning button A5" is a term in the product and applications description enclosed
with the Siemens line/area coupler 5WG1 140). Press the key again to revert to
normal operation.

LED A4 (above the "learning button" A5) indicates whether the coupler is in
programming mode:

•

LED off

Normal operation (communication via KNX)

•

LED on, red

Programming mode (LED is extinguished automatically

once the device address has been adopted

)

.

The coupler switches to programming mode only if the bus power is available.

Introduction

Note

Addressing the couplers

Note

Programming mode

Programming mode,
Siemens couplers

LED indicator A4

Bus power

«
...
54
55
56
57
58
...
»

Summary of Contents for OZW775

























































































































Reviews:

No comments

Related manuals for OZW775

Brand: Medion Pages: 220

Brand: Bose Pages: 2

Brand: Coby Pages: 1

ETR 2000 series

Brand: Delco Pages: 34

Brand: Planet Pages: 51

Brand: SPINOGY Pages: 27

Brand: AMS Pages: 14

Brand: Gamma Vacuum Pages: 43

Brand: Samsung Pages: 69

DCN-CONCM Concentus

Brand: Bosch Pages: 2

DCN Next Generation 4.41

Brand: Bosch Pages: 14

DCN-CON Concentus Delegate Unit

Brand: Bosch Pages: 2

Brand: Bosch Pages: 46

Brand: Bosch Pages: 38

Brand: Bosch Pages: 32

Brand: Bosch Pages: 2

Brand: Bosch Pages: 70

Brand: Bosch Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands