Siemens OZW775 Basic Documentation Download Page 45 | Manualshive

Page: 45 / 120

background image

45/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Device addresses via ACS

30.08.2007

5.5

Device address for the QAX910 central
apartment unit

The QAX910 central apartment unit device address can be set on the associated
operating page (display) and via the programming mode of ACS Service.

The procedure for commissioning is described in the mounting and commissioning
instructions, sheet C2707 (enclosed with every device).

The central apartment unit is delivered with the "Bus power supply" set to
"On".

In addition to its own intrinsic consumption, the QAX910 central apartment unit
when set to "Bus power = On" delivers the bus power supply for one OZW771
central communication unit or for the OCI700 service interface.

If other devices are installed on the same line, the central apartment unit must be
set to "Bus power supply = Off". The path for these settings is:

Main menu > Commissioning > Bus communication

Commissioning

Basic configuration…

RF connections…

Device list…

Bus communication…

Basic settings > Bus power supply

Basic settings

Device address 255

Bus power supply On

Programming mode Off

Bus power supply

Off

On

9

If "Bus power supply = Off" the central apartment unit receives the required bus
power from a decentral or central bus power supply, i.e. the power consumption of
the central apartment unit must be included in calculations (see section 2.2.2).

The QAX910 central apartment unit is factory-set with device address 255. For
communication via KNX, this device address must be modified.

If there are no couplers or IP routers, the factory-set area/line address 0.2 is used.

Introduction

Note

Caution!

Bus power supply

Note

Device address

«
...
43
44
45
46
47
...
»

Summary of Contents for OZW775

























































































































Reviews:

No comments

Related manuals for OZW775

Brand: Fagor Pages: 103

Brand: Dahua Pages: 58

Brand: Lars Thrane Pages: 141

Brand: N-Com Pages: 20

Brand: N-Com Pages: 28

Brand: cinetto Pages: 56

Brand: Parklio Pages: 12

Brand: ALLEN & HEATH Pages: 14

Brand: Nakamichi Pages: 11

Brand: Jazz Pages: 12

Brand: RCA Pages: 20

Brand: Boss Audio Systems Pages: 20

Brand: AudioBahn Pages: 13

Brand: Bogen Pages: 23

Brand: Sony Pages: 2

Brand: Sony Pages: 2

CMTDX2D - Micro System

Brand: Sony Pages: 2

CMTBX5BT - CMT Micro System

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands