Siemens OZW775 Basic Documentation Download Page 40 | Manualshive

Page: 40 / 120

background image

40/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Device addresses via ACS

30.08.2007

5.2.3

Assigning addresses in programming mode

"Address assignment in programming mode" is suitable for Synco 700 type RM…
controllers, RXB/RXL room controllers, OZW77x central communication units and
area/line couplers and IP routers.

Refer to the individual product documentation for details of how to set a device to
programming mode on site. Often, as with the Synco 700 RM… controllers, the
button marked "Prog" has to be pressed briefly.

Only one device at a time should be set to programming mode.

Explanation: If two or more devices are set to programming mode, the service tool
cannot identify an individual device and transmit a device address specifically to
that device.

1.

Set the required device to programming mode

locally

,

e.g. press the "Prog"

button on the RMU730. The red "Prog" LED lights up.

2. In ACS Service select

Plant > Edit device list…

to open the "Edit device list" dialog

box.

3. The

Programming mode…

button is now available under "Address assignment".

Click this button to open the "Address assignment" dialog box.

4. Enter a device address in the range 1…253 (excluding 150), and click

Write

to

confirm.

5. Check: Once the new address has been adopted, the LED on the device should

be OFF.

Setting devices to
programming mode on
site

Procedure

«
...
38
39
40
41
42
...
»

Summary of Contents for OZW775

























































































































Reviews:

No comments

Related manuals for OZW775

CQ-C7413U? CQ-C7113U

Brand: Panasonic Pages: 22

ConferenceSHOT AV

Brand: VADDIO Pages: 114

Brand: Xantech Pages: 102

Brand: AeroAudio Pages: 8

Brand: Nolan Pages: 48

Brand: Ramsey Electronics Pages: 2

Brand: Madas Pages: 58

AeGIS 9100CR200

Brand: PACH & COMPANY Pages: 49

Brand: Cary Audio Design Pages: 41

DE-3000+ Series

Brand: Altronic Pages: 77

Brand: Kitsound Pages: 10

Brand: Roger Technology Pages: 8

SoundStation 2W

Brand: Polycom Pages: 46

Brand: iEast Pages: 16

Brand: PulseAudio Pages: 16

Brand: jWIN Pages: 16

RS2767i/RS2767iF

Brand: RCA Pages: 2

Brand: RCA Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands