manualshive.com logo in svg

Siemens NK8237 MP4.81-01, Installation Manual, Page: 17 / 86

Share
Download
Siemens NK8237 MP4.81-01 Installation Manual Download Page 17

Structure and functions 

4 

NK8237 hardware 

 

17 

Building Technologies 

 

A6V10854379_a_en 

CPS Fire Safety 

 

30.11.2017 

6

 

Structure and functions 

6.1

 

NK8237 hardware 

The NK8237 is composed of an electronic board installed in a compact and robust 

plastic box. 

 

 

Note: NK8237 units with build state up to 01 are equipped with the NKM8001-A1 

mainboard and NK8237 units with build state 10 or higher are equipped with the 

NKM8001-A2 mainboard. 

 

 

NK8237 gateway unit 

6.1.1

 

Front panel 

The front panel houses 9 LEDs. 

Left Side LEDs 

The five LEDs on the left side are from top to bottom: 
Power (green LED) 
Power (hardware – controlled). 
Vital functions (green LED) 
Software vitality: 

   

Blinking (1 flash): core software running. 

   

Blinking (2 flashes): core software running and logging function active. 

Tamper (bi-color LED) 
Unit tamper: 

   

Red means tamper alarm (hardware controlled). 

   

Green means tamper disabled (from management station). 

Download (red LED) 
Network diagnostics: 

   

Off: status OK. 

   

Blinking (1 flash): missing identification from NS8xxx. 

   

Blinking (2 flashes): not used. 

   

Blinking (3 flashes): FTP channel open (default mode; for switch settings see 

Internal DIP Switches. 

   

On: critical/hardware fault. 

Summary of Contents for NK8237 MP4.81-01























































































Reviews:

No comments