manualshive.com logo in svg

Siemens MOTOX BA 2010, Operating Instructions Manual, Page: 62 / 124

Share
Download
Siemens MOTOX BA 2010 Operating Instructions Manual Download Page 62

Service and maintenance 

 

8.2 Checking and changing lubricants 

 

BA 2010 

60

 

Operating Instructions, 02/2018, A5E38093846A/RS-AC 

 

Note 
Where tandem gearboxes are concerned, each individual gearbox is to be considered 

separately. 
Gearbox sizes 28 and 38 on the 2nd gearbox are lubricated for life. An oil change is not 

required. 

 

8.2.2

 

Checking the oil level 

 

 

NOTICE 
The volume of gearbox oil changes with temperature 
If the temperature rises, the volume increases. Where temperature differences and filling 

quantities are significant, the volume difference can amount to several liters. 
The oil level must therefore be checked while still slightly warm, approximately 30 minutes 

after switching off the drive unit. 

 

 

①

 

Specified oil level 

②

 

Maximum oil level 

③

 

Minimum oil level 

Figure 8-1 

Oil level in the gearbox housing 

Table 8- 2 

Minimum and maximum fill levels x 

Oil level hole 

∅

d2 

Fill level x 

Tightening torque 

[mm] 

[mm] 

[Nm] 

G 1/8" 

14 

2.5 

10 

G 1/4" 

18 

3 

10 

G 3/8" 

22 

4 

25 

G 3/4" 

32 

7 

50 

Summary of Contents for MOTOX BA 2010





























































































































Reviews:

No comments